您知道水冷散热器如何安装吗？不知道的朋友也不要着急，接下来昊丰科技与您分享水冷散热器如何安装。

 

第一步：准备工作

 

准备工作是比较难的部分。在安装水冷系统之前，必须先将主板拆下来。也就是说必须先打开机箱，拔掉主板上的一切的卡和线缆。在拔出卡和线缆时，注意握住连接器部分使力，不要拉住连接线缆使力。（注意：请留心记下各部分连接配置，因为你随后还要将它们接回原样）。

 

第二步：拆除散热器

 

1、拆下主板之后，将散热器也拆下来。主板散热器位于芯片的中央，上面还带着一个风扇。注意不要损坏主板上的芯片。在拆除时注意用力不要过猛，要轻柔使力因为热胶已经将芯片与散热器牢固地粘合在一起。然后用酒精清除芯片顶部暴露出来的部分，然后涂上热胶。

 

2、将水冷散热器的扣具安装在主板背面，并根据CPU插槽类型（775775、1150、1156）在对应的螺丝孔上，安装好专用的固定螺丝，安装好后，主板就可以安装到机箱内部了。

 

3、接下来就是将CPU水冷散热器安装在主板正面CPU上了。

 

4、然后将水冷散热器安装到CPU上，这里注意需要将固定卡扣螺丝，也安装上。

 

5、安装好后，将固定螺丝与之前安装在主板背面的扣具固定即可。

 

6、别忘了把散热器，安装在机箱侧面的散热器模块上。

 

7、至此，我们就成功的完成CPU水冷散热器的安装了。水冷散热器安装成功后，用户还可以进入Bios中设置CPU风扇的转速等，大家根据自己的情况调节，灵活调节，以达到更好的静音和节能效果，默认一般不调节也可以。

Do you know how to install a water-cooled radiator? Do not know friends also do not worry, next Haofeng technology and you share how to install water-cooled radiator.
Step 1: Preparation
Preparation is the hard part. Before installing the water cooling system, the motherboard must be removed. In other words, you must first open the chassis and pull out all the cards and cables on the motherboard. When pulling out the card and cable, pay attention to holding the connector part of the force, and do not pull the connecting cable force. (Note: Keep an eye out for the parts of the connection configuration because you will then have to bring them back as they were).
Step 2: Remove the radiator
After removing the motherboard, remove the radiator. The motherboard radiator is located in the center of the chip and has a fan on it. Be careful not to damage the chip on the motherboard. Be careful not to push too hard when removing it, but to use it gently because the hot glue has bonded the chip to the radiator. The top of the chip is then cleaned with alcohol and then coated with hot glue.
2, install the water-cooled radiator buckle on the back of the motherboard, and according to the CPU slot type(775775, 1150, 1156) on the corresponding screw hole, install the special fixed screw, after installation, The motherboard can be installed inside the chassis.
3, the next is to install the CPU water-cooled radiator on the motherboard front CPU.
4, and then install the water-cooled radiator on the CPU, here pay attention to the need to fix the clasp screw, also installed.
After installation, fix the fastener and the fastener previously installed on the back of the motherboard.
Don't forget to install the radiator on the radiator module on the side of the chassis.
At this point, we successfully completed the installation of the CPU water-cooled radiator. After the installation of the water-cooled radiator is successful, the user can also enter the speed of the CPU fan set in Bios. Everyone can adjust and adjust flexibly according to their own conditions to achieve better silent and energy-saving effects. The default is generally not adjusted.